Sole-control-remotes TT8 Manuel d'utilisateur

PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFOREOPERATING YOUR NEW TREADMILL!TT8OWNER’S MANUAL

TT8-9- Step7..1. Install the four speed Nuts (84) on the motor cover (43).2. Install the Motor Base Caps (39,40) with the six 5x16mm Tapping Screws (

TT8-10-TT8Carefully lift the treadmill at the rear roller area, grasping the two side end caps, and roll thetreadmill away.Transport

TT8-11-WGetting familiar with the control panelTT8 ConsoleGetting Started:Power the treadmill on by plugging it into an appropriate wall outlet, then

TT8-12-Quick-Start Operation:STEP 1: Press and release any key to wake display up (if not already on).Note: Installing the tether key will also wake u

TT8-13-LED is lit the Dot matrix displays the Speed profile and when the Incline LED is lit the Dot Matrixdisplays the Incline profile. You may change

TT8-14-time. After adjusting the time, press enter. (Note: You may press start at any time during theprogramming to begin with only settings you have

TT8-15-The old motto, no pain, no gain, is a myth that has been overpowered by the benefits ofexercising comfortably. A great deal of this success

TT8-16-How to wear your wireless chest strap transmitter:1. Attach the transmitter to the elastic strap using the locking parts.2. Adjust the strap as

TT8-17-How the Heart Rate Control Program Works:Heart Rate Control (HRC) uses your treadmill's speed and incline systems to adjust your heart rat

TT8-18-Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance ismaximized when the bed is kept as clean as possible. U

TT8-1- Product Registration2Important Safety Instructions3Important Electrical Information

TT8-19-TREADBELT TRACKING ADJUSTMENT:The performance of your treadmill is dependent on the frame running on a reasonably levelsurface. If the frame is

TT8-20-Belt/deck lubrication procedure:Do not lubricate with other than SOLE approved lubricant. Your treadmill comes with one tube oflubricant and ex

TT8-21-Before contacting your dealer or SOLE service for aid, please review the following information. Itmay save you both time and expense. This list

TT8-22-Calibration procedure:1) Remove the safety key2) Press and hold down the Start and Fast (speed up) buttons with one hand and replace the safe

TT8-23-Effective January 1, 2007TREADMILL WARRANTYSOLE warrants all its treadmills parts, for a period of time listed below, from the date of retail

TT8-2-Thank you for your purchase of this quality treadmill from SOLE. Your new treadmillhas been manufactured by one of the leading fitness manufactu

TT8-3-WARNING - Read all instructions before using this appliance.DANGER - To reduce the risk of electric shock disconnect your SOLE treadmill from th

TT8-4-WARNING!NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Largeswitching currents of the drive motor will trip

TT8-5-NEVER operate this treadmill without reading and completely understanding the results of anyoperational change you request from the computer.

TT8-6-#125. 3/8 x1-3/4Button Head Socket Bolt (4pcs)#63.Safety Key (1pc)#18.Lubricant (1pc)#105.M6 Allen Wrench (1pc)#104. Combination M5 Allen Wren

TT8-7- Step 1.Remove the treadmill from the carton and lay it aside on a hard, level surface. Step 2.Connect the Computer Cable (32) with Computer C

TT8-8- Step4.Connect the Speed Switch Cable (37) with the upper Speed Cable (34).Connect the Incline Switch Cable (38) with the upper Incline Cable (